Line # Part# Description
100-440 REPLACEMENT 3.73/1 BTR AXLE
100-445 AXLE MOUNTING SHIMS FOR BTR AXLE
100-446 COMPENSATOR ADAPTOR FOR BTR
1 100-421 REBUILT 3HA AXLE 3.7/1
2 100-426 CARRIER 3HA 3.7/1
2 100-427 CARRIER 3HA 4.1/1
3 100-434 3HA RING AND PINION 3.7
3 100-435 3HA RING AND PINION 4.1
3 100-429 7HA PHASE 2 RING AND PINION 4.1
4 100-463A SIDE GEAR 7HA
5 100-463F THRUST WASHER FOR SIDE GEAR
6 100-463B PINION MATE 7HA
7 100-463G THRUST WASHER PINION MATE
8 100-463D THRUST BUTTON
9 100-463C CROSS PIN
10 100-463E LOCKING PIN (FOR CROSS PIN)
13 100-144 CARRIER BEARING 3HA
13 100-149 CARRIER BEARING 7HA PHASE 1
13 100-149A CARRIER BEARING 7HA PHASE 2
14 100-468 CARRIER SHIM .003 3HA/7HA-2
14 100-468A CARRIER SHIM .005 3HA/7HA-2
14 100-468B CARRIER SHIM .010 3HA/7HA-2
14 100-468C CARRIER SHIM .030 3HA/7HA-2
14 100-469 CARRIER SHIM .003 7HA-1
14 100-469A CARRIER SHIM .005 7HA-1
14 100-469B CARRIER SHIM .010 7HA-1
15 100-173 IN PINION BEARING 3HA & 7HA-1
15 100-173A IN PINION BEARING 7HA PHASE 2
16 100-466 PINION SHIM .003 3HA/7HA-1
16 100-466A PINION SHIM .005 3HA/7HA-1
16 100-466B PINION SHIM .010 3HA/7HA-1
16 100-467 PINION SHIM .003 7HA -2
16 100-467A PINION SHIM .005 7HA -2
16 100-467B PINION SHIM .010 7HA -2
17 100-169 OUTER PINION BEARING 3HA
17 100-175 OUT PINION BEARING 7HA PHASE-1
17 100-175A OUT PINION BEARING 7HA PHASE-2
18 100-470 PINION PRELOAD SHIM .003 3HA
18 100-470A PINION PRELOAD SHIM .005 3HA
18 100-470B PINION PRELOAD SHIM .010 3HA
18 100-470C PINION PRELOAD SHIM .030 3HA
18 100-471 PINION PRELOAD SHIM .003 7HA
18 100-471A PINION PRELOAD SHIM .005 7HA
18 100-471B PINION PRELOAD SHIM .010 7HA
18 100-471C PINION PRELOAD SHIM .030 7HA
20 100-141 REAR AXLE BEARING
21 100-528 AXLE SHAFT
22 100-548 REAR AXLE KEY
23 100-527 REAR AXLE WASHER
24 100-525 REAR AXLE NUT FINE 3HA
24 100-526 REAR AXLE NUT COARSE
25 100-529 COTTER PIN
26 100-462 3HA COVER GASKET
26 100-463 7HA COVER GASKET
27 100-002 REAR AXLE SEAL
28 100-458 SHIM .003
28 100-459 SHIM .005
28 100-460 SHIM .010
29 100-453 BEARING RETAINING PLATE
30 100-452 GASKET
31 100-451 OIL SEAL SPACER PLATE
32 100-450 RETAINER ONLY
33 100-001 REAR HUB SEAL
34 100-901 BOLT/WASHER/NUT
35 100-603 GREASE FITTING
36 100-003 PINION SEAL 3HA
37 100-004 PINION SEAL 7HA UP TO 1981
38 100-003A 3HA FLANGE SLEEVE
38 100-004A 7HA FLANGE SLEEVE
40 100-456 3HA PINION NUT
40 100-457 7HA PINION NUT
41 100-447 DRAIN PLUG
44 100-546 REAR W/W HUB LH
44 100-546A REAR W/W HUB RH
45 100-545 REAR HUB-DISC WHEEL
45 100-553 REAR HUB REPAIR SLEEVE
46 100-550 DRUM RETAINING SCREW
47 100-547 REAR LUG BOLT
48 100-684 LUG NUT
49 100-549 W/W DRUM BOLT
50 100-552 DRUM ALIGNMENT SCREW
59 100-410 DIFFERENTIAL ASSEMBLY +4,4/4
60 100-411 SIDE GEAR - POWER LOC
61 100-412 PINION MATE - POWER LOC
62 100-413 CROSS PIN SHAFT - POWER LOC
63 100-414 ROLL PIN
64 100-415 THRUST BUTTON
65 100-416 RING
66 100-417 FRICTION PLATE FLAT
67 100-418 FRICTION PLATE DISHED
73 100-498 7HA DRIVE SHAFT ASSEMBLY
74 100-500 U/JOINT +4 & +8
75 100-501 GREASE FITTING
76 100-502 DRIVESHAFT CORK SEAL WASHER
77 100-505 DRIVE SHAFT BOLT KIT
   


Click thumbnail for pop-up

Now available:
New axle shafts for +4 and 4/4
#21 in the picture.

Available now, direct replacement rear axle
assemblies for 4/4 and +4 Morgans

These units come with all new internals and
can be built with either standard or power-loc
diffs. Gear ratio's available are 3.08 to 4.56.
Only modification needed is for cars fitted with
a 7HA to shorten the driveshaft 1 inch.

We recently sold one of these to a +4 owner
in Ca. with a 3.08 ratio and his responce was
that it was like driving a new car. At 60 MPH
instead of the engine turning 3000RPM it now
turns 2300RPM and turns 3000RPM now at
75MPH.

And he can still pass cars at 60 in 4th gear!

Call now for current pricing.

(888) 345-6647